For ProfessionalsPERTHERM PLR
Thermal Insulation Sheet Plaster
DESCRIPTION
The product is a cement-based, fiber-reinforced polystyrene thermal insulation sheet (EPS, XPS, ROCKWOOL) plaster containing mineral aggregates of a special particle size, and chemical additives improving product performance.
It conforms to TS EN 998-1 of July 2011.
FEATURES
| Appearance | Grey |
| Mixing Ratio | 6-6.5 lt water /25 kg |
| Amount of Consumption | 4 – 5 kg/m2 (depending upon application type) |
| Application Temperature | +5 oC to +35 oC |
| Time for Use | 40-60 minutes |
| Vessel Life | 3 hours |
| Toxicity | Non-toxic |
| Splice Strength | >1 N/mm2 |
| Bending Strength | 2 N/ mm2 Min. |
| Pressure Strength | 6 N/ mm2 Min. |
| Water Absorption | ≤ 0.40 kg/m2 min.05 W2 |
| Time Until Complete Freezing | 7 days |
| * The above values are valid for + 23oC and 50% relative humidity. The time is shortened at high temperatures and extended at low temperatures. | |
AREAS OF USE
Polystyrene is applied on surfaces requiring elastic ability at interior and exterior applications of all buildings constructed from polystyrene hard foam (EPS, XPS) where Rockwool insulation sheets are applied.
BENEFITS
It is easy to prepare and apply. It gives proper working time. It does not lead to drift at vertical applications. It has high adhesion properties. It is resistant to freeze-thaw cycling.
INSTRUCTIONS FOR USE
The thermal insulation sheets to be plastered should be sound, well adhered to the underlying surface, and be clean and dry. The gaps between the plates should be filled with the same insulation material or foam.
25 kg of EKOKAT PERTHERM PLR is slowly poured onto 6-6.5 liters (e.g. 24-26%) of clean water and is then mixed with a low speed mixer or a trowel until a homogenous mixture is obtained. It is allowed to rest for 5 to 10 minutes and mixed again for 1 to 2 minutes. It is applied onto the plaster surface with a minimum thickness of 2 mm, and the plaster mesh is placed such that it would overlap by at least 10 cm.
At the corners as well as at all girder, window, and door frames the plaster mesh should be rotated for at least 20 cm, and the corner profiles should then be placed. After the first coat is dried, the second coat is applied. The prepared mortar should be consumed within 2-3 hours. Do not apply above 35 ° C or below + 5 ° C. It should not be applied under very humid and / or hot weather conditions, or onto such surfaces that are being melted or are subject to the danger of frost within 24 hours.
PACKAGING
25 kg craft bags (PE reinforced)
64 shrink bags on one palette (110x110 cm).
STORAGE CONDITIONS AND SHELF LIFE
No more than two palettes should be placed on top of each other in their unopened original packaging, in a cool and dry environment. Shelf life is 12 months from date of production under suitable storage conditions.
SAFETY MEASURES
Work clothes, protective gloves, goggles and masks suitable for workers health and safety should be used during the application. Due to irritant effects of uncured material, it should be washed with plenty of water and soap immediately in case of contact with skin and eyes. If swallowed, seek medical advice immediately. No food and drink should be brought into application areas. Store it out of reach of children. Please refer to the safety data sheet for further information.
RESPONSIBILITY
Our Company may not be held liable for any application errors that might be suffered if the product is not used for its intended purposes, or if it is failed to conform to the conditions and proposals specified above regarding technical application. This technical data sheet contains information that is current as of the date of issuance hereof. The manufacturer hereby reserves its right to change this data sheet at any time.
- EK 3002.010.25
- Grey
